Load Ports
013096-336-20
Brooks Automation TLG-I2-FL6M-01 RFID Transponder Reader Kit
About this part
Brooks Automation part 013096-336-20 is a TLG-I2-FL6M-01 low-frequency RFID transponder reader configuration for the FixLoad 6M semiconductor wafer load port. The reader uses an RS232 serial interface and the Brooks ASC-I1 protocol to read and write passive carrier-identification transponders. Surplus configurations show the reader paired with the dedicated ANT-ID2-INFIXR6M antenna; this is a load-port identification component rather than a complete FixLoad load port
Configurations vary. Verify the exact unit before choosing a replacement.
No archived photo available
Key Facts
Specifications
| Brooks part number | 013096-336-20 |
| Reader configuration | TLG-I2-FL6M-01 |
| Reader family | TLG-RS232 |
| Application | Brooks FixLoad 6M semiconductor wafer load port |
| Communication protocol | ASC-I1 |
| Host interface | RS232 serial |
| RFID frequency | 134.2 kHz |
| Function | Read/write operation with passive, battery-free inductive transponders |
| Typical complete reading cycle | Less than 100 ms |
| Serial data rate | 300 baud to 115.2 kbaud |
| Reader addressing | Addresses 0 through E; factory setting 0 |
| Supply voltage | 18–30 VDC; 24 VDC nominal |
| Maximum read repetition rate | 4 operations per second |
| Maximum programming repetition rate | 1 operation per second |
| Operating temperature | 0 to 50 °C (32 to 122 °F) |
| Storage temperature | −25 to 70 °C (−13 to 158 °F) |
| Permissible humidity | 25–80% at 50 °C |
| Ingress protection | IP40 |
| Housing material | ABS, UL 94 V-0 |
| Fuse | 500 mA time-delay, TR5 housing |
Configuration boundary
The FL6M-configured reader is a carrier-identification component installed on a FixLoad 6M load port. Specifications identified as RS232-reader-family data describe the Brooks ASC-I1 reader platform; antenna geometry, harness termination, and mounting provisions are specific to the FL6M integration and should be matched by exact configuration number.
Reader-level serial connections
The Brooks ASC-I1 manual documents two reader-level RS232 connections. An installed FixLoad kit may route these signals through a system harness, so the load-port harness must not be inferred solely from this reader pinout.
| Connector | Pin | Signal |
|---|---|---|
| 4-pin RS232 interface 1 | 1 | Not connected |
| 4-pin RS232 interface 1 | 2 | Ground |
| 4-pin RS232 interface 1 | 3 | RxD |
| 4-pin RS232 interface 1 | 4 | TxD |
| DB9 female RS232 interface 2 | 2 | TxD |
| DB9 female RS232 interface 2 | 3 | RxD |
| DB9 female RS232 interface 2 | 5 | Ground |
| DB9 female RS232 interface 2 | 1, 4, 6, 7, 8, 9 | Not connected |
Installation and service notes
- Calibrate the installed antenna with the reader's automatic tuning function before operation.
- The reader is intended for an indoor industrial environment and for installation and operation by trained personnel.
- A successful tuning cycle extinguishes the tuning indicator; a blinking indicator denotes a tuning or antenna fault.
- A transponder page that is locked through the ASC-I1 command set cannot subsequently be unlocked.
Documentation Downloads
Local PDF copiesPart Photos
0 imagesHistorical archive images for identification, labels, connectors, and condition reference, not current inventory.
Historical Listings & Prices
Historical listing data, not a current offerThe typical recorded price range is $34.00 to $66.00. Based on 2 archived listing records; not a current offer, appraisal, or confirmed sale price.
View archived listing titles
- Brooks Automation FIXLOADT 6M Kit - NEW - P/N: 013096-336-20